Electrolux FAC124P1A Provozní pokyny stáhnout pdf (Strana 55)

Section 3 Electronic Control

3-3

TIMER BUTTON

For Delay Stop, the unit must be in the ON position.

For Delay Start, the unit must be in the OFF position.

When TIMER Mode is selected the LED will illuminate

above the button.

To adjust timer setting, tap or hold the UP arrow (^) or

DOWN arrow (v) to change the delay time by .5 hour

increments up to 10 hours, then by 1 hour increments

up to 24 hours. The control will count down the timer

remaining until start (8, 7.5, 7, etc.). The Delay Start

mode automatically selects cooling with maximum Fan

Speed. The temperature maintained will be the same

as previously set. To change the set temperature,

press “COOL” then Up or Down arrows until the desired

temperature is indicated on the display. After 5 seconds,

the control will automatically change the display back to

the hours remaining until the unit will start/stop. Turning

the unit “ON” or “OFF” at any time will cancel the Delay

Start/Stop function. The delay Start/Stop feature will

work until the unit either starts or stops. Once this has

happened then the above steps have to be repeated

again.

SLEEP MODE BUTTON

Press the SLEEP Mode button to activate this feature.

The LED will illuminate above the button. In SLEEP Mode

the selected cooling temperature will increase by 2°F 30

minutes after the mode is selected. The temperature

will then increase by another 2°F, after an additional

30 minutes. This new temperature will be maintained

for 7 hours before it returns to the originally selected

temperature. This ends the SLEEP Mode and the unit

will continue to operate as originally programmed. The

SLEEP Mode program can be cancelled at any time during

operation by pressing SLEEP Mode button.

CLEAN AIR BUTTON

Press the CLEAN AIR button to activate this feature. The

LED will illuminate above the button. When this feature

is turned ON, the electronic air puriﬁ er is energized to

remove pollen and impurities from the air. To cancel this

feature, press the CLEAN AIR button and the LED will

turn OFF and the electronic air puriﬁ er will shut off.

This feature can only be activated at the unit touchpad

only.

REMOTE SENSING FEATURE (on some models)

This feature is activated from the remote control only.

To activate the remote sensing feature, point the remote

control towards the unit and press the remote sensing

start button. The LIGHT on the unit control will pulse

to indicate it received the signal. The LIGHT on the

remote control will pulse each time it sends a signal.

It will continue to send this signal until the feature is

deactivated by pressing the remote sensing stop

button. If the unit does not receive the remote sensing

signal during any 3 minute interval, the unit will keep

indicating the remote sensing mode has ended. The

display on the remote control indicates the temperature

at the remote. The unit display indicates the set

temperature.

CHECK FILTER BUTTON

This feature is a reminder to clean the air ﬁ lter for more

efﬁ cient operation and cooling. The LED indicator will

illuminate after 250 hours of operation. To reset after

cleaning the ﬁ lter, press the CLEAN FILTER button and

the light will go off.

FAHRENHEIT /CELSIUS

The control is capable of displaying temperature in

degrees Fahrenheit or degrees Celsius. To convert from

one to the other, press and hold the UP and DOWN

Temperature Selection Buttons at the same time for 3

seconds.

FAULT CODES

If the display reads “ES” or “AS” a sensor has failed.

The “ES” is for the evaporator thermistor and the “AS” is

the ambient thermistor located in the remote control.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 139 140

Komentáře k této Příručce

Žádné komentáře

Electrolux FAC124P1A Provozní pokyny Strana 55

Komentáře k této Příručce

Související produkty a manuály pro Split-systém klimatizace Electrolux FAC124P1A