Electrolux EASX24C5ATLW Uživatelský manuál

INSTRUCTIONS MANUALSPLIT TYPE ROOM AIR CONDITIONERMODELS:Please read this manual completely before operating your room air conditioner.140721AS6(06-0

Outdoor Unit1. The outdoor unit must be installed at a convenient site that is not exposed to strong winds. The site should be dry and well ventilate

Parts listNUMBERING PART NAMEInstallation plateClip anchorSelf-tapping screw A ST3.9x25SealDrain JointQTY.12345615-85-811Connectingpipeassembly*Liquid

1. This illustration is for explanation purposes only.2. Copper lines must be insulated independently754231Indoor unitOutdoorunit66More than 12cmMor

Indoor unit installationInstallation plate descriptionindoor unit installation electrolux 12454145414543 electrolux how the air conditioner worksOptim

Fixing the installation plateDrilling the Hole1. Install the installation plate horizontally over the structural parts on the wall using the spaces i

Do not put the endof drain hose into water.Do not blockwater flowby a rise.Connective pipe and drainage installationDrainage1. Run the drain hose slo

Piping and wrapping1. Bundle the tubing, connecting cable, and drain hose with tape securely, evenly as shown.2. Because the condensed water from re

1. Install the outdoor unit on a rigid base to prevent increasing noise level and vibration.2. Determine the air outlet direction where the discharged

Air outletOutdoor unit dimensionmm - (WxHxD)Mounting dimensionsA(mm)B(mm)24k Btu modelsSettlement of outdoor unitAnchor the outdoor unit witha bolt an

Flaring workMain cause for refrigerant leakage is due to defect in the flaring work.Carry out correct flaring work using the following procedure:1. Cu

Thank you for choosing Electrolux. This manual contains all of the information required to guarantee your safety and the appropriate use of your air c

4. Flaring workA) Firmly hold copper pipe in a die in the dimension shown in the table below.1,31,61,82,2Máx.0,71,01,02,0A (mm)Mín.OUTERDIAMETER (mm)6

Electrical work1. If there is serious safety problem about the power supply, the technicians should refuse to install the air conditioner and explain

Electric safety regulations for the initial Installation1. If there is serious safety problem about the power supply, the technicians should refuse to

electrical work electrolux 22Before performing any electrical work, turn off the main power to the system.1. The inside and outside connecting cable c

1. Remove the electrical control board cover from the outdoor unit by loosening the screw.2. Connect the connective cables to the terminals as identif

For 24k Btu modelsTerminal block of outdoor unitelectrical work electrolux 24For 8k, 12k and 18k Btu models1342(N)To indoor unitModel BTerminal block

1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of wiring, be guided by the circuit diagram

Air purging with vacuum pump1. Check that each tube(both liquid and gas side tubes) between the indoor and outdoor units have been properly connected

Manifold valveCompound meter-76cmHgHandle LoHandle HiCharge hoseCharge hoseVacuum pumpPressure gaugeLow pressure valveWhen using the vacuum pumpFor me

Contents01. Welcome...0102. Environmental advic

03 electrolux contentsThe air conditioner that you have bought may be slightly different from the one illustrated in this manual. Please refer to the

To prevent injury to the user or other people and property damage, the following instructions must be followed.Incorrect operation due to ignoring of

conditioner. It contains contaminants and could make you sick.10.Do not use the power cord close to heating appliances. It may cause fire and electric

20.Ventilate the room well when used together with a stove, etc. An oxygen shortage may occur.21.When the unit is to be cleaned, switch off, and turn

falling of unit.28.Always insert the filters securely. Clean filter once every two weeks. Operation without filters may cause failure.29.Do not place

7. The indoor unit must be at least 2.3 meters (7.5 feet) from the ground.8. The site must allow for the easy removal of the connector pipe and drai