Electrolux EYL10566BT Uživatelský manuál

EYL85066BTEYL95066BTEYL10566BTWATER HEATER USER MANUAL

10 www.electrolux.com Isolating stop valveMains water supplyShower unitBath spillover levelHose retainerMinimum 25mm between showerhead and sp

11ENGLISH5. INSTALLATION5.1 Select the location and hang up the showerWhile planning your shower installation, make sure you allow sufcient clearance

12 www.electrolux.com Bottom left inlet entryTop left inlet entryRear left inlet entryTop right inlet entryLeft inlet entryScrew the top xing

13ENGLISHTo remove the water inlet coverTo change the water inlet positionThe factory default setting of the water inlet position is on the right side

To select the wiring terminal position5.3 Electrical wiring connectionConnect the mains water supply to the water inlet by using a 15MM pusht(not sup

Fig. 7aTurn the stabiliser valve spindle fully clockwise until resistance is felt.1.Stabiliser valveWater ow position2. Adjust the spline spindle and

Sliding rail(without a hold)Fig 11Sliding rail bottom(withahold)To install the assembly of the sliding rail.4.a.Assemble the sliding seat into the sli

c.Assemble the soap tay on the soap tray holder.d.Place the sliding rail between the holders and x the sliding rail by xing the lower holder as Fig.

6.2Before normal operation of the shower, it is essential that the following commissioning procedure is completed correctly.The following operation is

6. When a smooth ow of water is obtained, rotate the temperature control from Min to Max several times to release any trapped air within the unit.7.

2 www.electrolux.comWE’RE THINKING OF YOUThank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it decades of prof

SpraySpray-bubbleBubbleMassageWater ow DescriptionSettingWater ow DescriptionSettingWater ow DescriptionSettingWater ow DescriptionSettingWater o

7. MAINTENANCEInspect the ‘O’ ring for damage when the lter cap is removed.When cleaning the lter, DO NOT use a sharp object, as it will cause damag

8. HELPFUL HINTS AND TIPSTP – Temperature ProtectionAbnormal safety cut-outDuring normal operation if the temperature exceeds the showering safety lim

9. TROUBLESHOOTINGProblem/Symptom Cause Action/CureShower fail to operate, no water ow out.Interrupted power supply.Unit malfunction.Blown fuse or ci

9. TROUBLESHOOTINGProblem/Symptom Cause Action/CureShower varies fromnormal temperatureto cold during use.Water pressure hasdropped below minimumrequi

5519W17172-000-001www.electrolux.com/shop

3ENGLISHCUSTOMER CARE AND SERVICEWe recommend the use of original spare parts. When contacting Electrolux Customer Service, ensure that you have the f

Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect instal

The appliance must be earthed.The pressure relief device must be tted during installation, unless it is incorporated in the appliance.The appliance m

Remove all the packaging.Do not install or use a damaged appliance.All products manufactured and supplied by Electrolux are safe provided they are ins

Do not operate the shower unit if the showerhead or spray hose has been damaged or is blocked.2.3 DisposalDo not block the ow of water from the showe

8 www.electrolux.com 3. Electrical RequirementsMains electrical supplyShower unit30mA RCD for ampage of MCB/Fuse see circuit protection table

9ENGLISHThe current rating will be reduced if the cabling is bunched with others, surrounded by thermal loft or wall insulation or placed in areas whe