Electrolux B 99852G Uživatelský manuál

B 99852GUser ManualHob

10Customer CareService and Spare PartsWhen you contact the Service Centre, they will need the following information:1. Your name, address and post cod

11Guarantee ConditionsStandard guarantee conditionsWe, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electro

12Instructions for the InstallerEngineers technical dataBURNER ULTRA-RAPID SEMI-RAPID AUXILIARY(triple crown) (medium) (small)POSITION MAX MIN MAX MIN

13700 mm400 mm400 mm100 mm50 mm50 mm55 mm700 mm400 mm100 mm400 mm50 mm50 mm55 mmCLEARANCES REQUIRED WHEN FITTING THE GAS HOBWITHOUT A COOKER HOOD ABOV

14InstallationImportantThis hob must be installed by a competent person to the relevant Gas Standards.Any gas installation must be carried out by a re

15Cut Out SizeThe dimensions of the cut-out are given in the diagram.Building InBuilding over a cupboard or drawerIf the hob is to be installed above

16ON/OFF SWITCHFLEXOUTLETON/OFF SWITCHFLEXOUTLETFO 0763FO 076412Building over a kitchen unit with doorProper arrangements must be taken indesigning th

17Fitting the hob to the worktopBefore fitting the hob into the cut out, an adhesive seal must be fitted to the undersideoutside edge of the hob. It i

18Electrical connectionsAny electrical work required to install this hob should be carried out by a qualifiedelectrician or competent person, in accor

19Permanent ConnectionIn the case of a permanent connection, it is necessary that you install a double pole switchbetween the hob and the electricity

2 Important Safety InformationYou MUST read these warnings carefully before installing or using the hob. Ifyou need assistance, contact our Customer C

20Fault FindingPreliminary Electrical Systems CheckSTARTIsolate applianceand carry out:A: Earth Continuitycheck. Has inlet fuse blown?Carry out:C: Pol

21A. EARTH CONTINUITY CHECKAppliance must be electrically disconnected - meter set on Ω (Ohms) x 1 scale andadjust zero if necessary.— Test leads fro

22Check gas supply atburnerIgnition System / Gas IgnitionYESCheck plug top fuse andreplace if necessaryCheck polarity and earthcontinuity of supply po

23CommissioningWhen the hob has been fully installed it will be necessary to check the minimum flame setting. Todo this, follow the procedure below.1)

24AEG Haugeräte GmbHPostfach 1036D-90327 Nürnberghttp://www.aeg.hausgeraete.de© Copyright by AEGConversion from Natural Gas to LPGIMPORTANTThe replace

25

35686-0203 AM 05/06 Grafiche MDM - Forlìwww.aeg-electrolux.co.uk

3z Ensure the control knobs are in the ‘OFF’ position when not in use.z When using other electrical appliances, ensure the cable does not come into co

4This appliance is manufactured according to the following EEC directives:73/23 EEC - 90/683 EEC - 93/68 EEC -89/336 EEC - 90/396 EEC, current edition

51. Hob Top2. Semi-rapid Burners3. Auxiliary Burner4. Ultra-rapid Burner (triple crown)5. Control knobsDescription of the HobINSTALLATIONAny gas insta

6Hob burnersTo light a burner:z Push in the relevant control knob and turn it to maximum position.z Upon ignition, keep the knob pushed down about 5 s

7Maintenance and CleaningBefore any maintenance or cleaningcan be carried out, you mustDISCONNECT the hob from theelectricity supply.The hob is best c

8Pan SupportsTo keep the pan supports in the correct position, they are mounted on metal pinslocated in the back of the hob. After cleaning the hob, e

9Something Not Working?If the hob is not working correctly, please carry out the following checks before contactingyour local Service Force Centre.