(:*:... ...(1 :$6+,1*0$&+,1( 86(50$18$/
PROGRAMME OPTION BUTTONSDepending on the programme, differentfunctions can be combined. These must beselected after choosing the desired pro-gramme an
Soil Level Icon Type of fabricIntensive For heavy soileditemsNormal For normal soileditemsDaily For daily soileditemsLight For slightly soileditemsQui
Stand by : once the programme has finish-ed after a few minutes the energy savingsystem will be enabled. The brightness ofthe display is reduced. By p
Your appliance incorporates a recirculationsystem which allows an optimal use of theconcentrated detergent.Follow the product manufacturer’s recom-men
Programme - Maximum and Minimum Tempera-ture - Cycle Description - Maximum Spin Speed -Maximum Fabrics Load - Type of LaundryOptionsDetergent Com-part
Programme - Maximum and Minimum Tempera-ture - Cycle Description - Maximum Spin Speed -Maximum Fabrics Load - Type of LaundryOptionsDetergent Com-part
The washing temperature of the washing phase may differ from the temperature declared for the selected pro-gramme.CONSUMPTION VALUESThe data of this t
EXTERNAL CLEANINGClean the exterior cabinet of the appliancewith soap and water only, and then drythoroughly.Important! Do not use methylated spirits,
Warning! Before unscrewing the pumpcover, switch the appliance off andremove the mains plug from thesocket.Proceed as follows:1. Unplug the appliance.
has finished the cycle, and is empty. Whenrefitting the pump cover, ensure it is se-curely retightened so as to stop leaks andyoung children being abl
Electrolux. Thinking of you.Share more of our thinking at www.electrolux.comCONTENTSSafety information 2Safety instructions 3Product description
During machine operation it is possible thatthe red pilot light of button 8 blinks, one ofthe following alarm codes appears on thedisplay and some aco
Problem Possible cause/SolutionThere is water on the floor:Too much detergent or unsuitable detergent(creates too much foam) has been used.• Reduce th
Problem Possible cause/SolutionSpinning starts late or the machine does notspin:The electronic unbalance detection device hascut in because the laundr
2. Remove the power supply cable andthe draining hose from the hose holderson the rear of the appliance.3. Unscrew the three bolts.4. Slide out the re
RAISING THE APPLIANCESuspended wooden floors are particularlysusceptible to vibration.To help prevent vibration we recommendyou place a waterproof woo
Warning! Installation shouldcomply with local water authorityand building regulations’requirements.The appliance must be connectedto a cold water supp
3 pinMin. 60 cm (23.6”)Min. 90 cm (35.4”)The drain hose may be extended to a maxi-mum of 4 metres. An additional drain hoseand joining piece is availa
LoopImportant! Before connecting up themachine to new pipework or to pipeworkthat has not been used for some time, runoff a reasonable amount of water
SHOWERBATHBIDETWASHINGMACHINEDISHWASHERRAINWATER‘RUN-OFF’SURFACE WATERDRAINS & SEWERSUNTREATEDDISCHARGERIVERRIVERFOUL DRAINFOUL SEWERSSEWAGETREATM
This means that they can be recycled bydisposing of them properly in appropriatecollection containers.ECOLOGICAL HINTSTo save water, energy and to hel
• Obey the maximum load volume of 7 kg (refer to the “Pro-gramme chart” chapter).• If the supply cord is damaged, it must be replaced by themanufactur
on the inner side of the door. The distancebetween the holes hobs fixing centres mustbe 416 mm.The distance from upper edge of the doorto the centre o
8Front view5 mm Hardwood stripAdditional pieces oftimber should runfrom front to backDrill four fixing holes (see Fig. 9).9Top viewFront edgePosition
www.electrolux.com/shop132905971-A-032015
Water connection• Make sure not to cause damage to thewater hoses.• The appliance is to be connected to thewater mains using the new suppliedhose-sets
1 2 7 8 93456101Detergent dispenser drawer2Control panel3Door opening handle4Rating plate5Drain pump6Front adjustable feet7Water drain hose8Mains cabl
To disable this device and restore the pos-sibility of closing the door, rotate the buttoncounterclockwise until the groove is vertical.CONTROL PANELB
RINSE HOLDBy selecting this function the water of thelast rinse is not emptied out to prevent thefabrics from creasing. Before opening thedoor it will
The Selected delay set by pressing therelevant button appears on the display fora few seconds, then the duration of theselected programme is displayed
to the appliance. This function remains ena-bled also when the washing machine is notworking.There are two different ways to set this op-tion:1. Befor
Komentáře k této Příručce